| XA200352-H INA Slewing Ring Bearings | Da max.:67.4 mm; dk:63.881 mm; da max.:55 mm; Specific static load factor K0:300 N/mm²; Da min.:61.3 mm; d:44.45 mm; M:4 mm; d1 ≈:54.991 mm; r1 min.:1 mm; r2 min.:1 mm; Material constant KM:330; α:5 °; Lubricant:Regular relubricatio; Basic dynamic load rating C:170 kN; da min.:49.9 mm; Design (sliding contact surface combination):Steel/steel; b1:5 mm; Basic static load rating C0:510 kN; |
| XU08012 INA Slewing Ring Bearings | Tolerance shaft:e7; Tolerance housing:H7; Permissible sliding velocity v min.:0 m/s; Specific static load factor K0:45 N/mm²; Mass bushing:3.75 kg; Coefficient of friction µ max.:0.15; D1:165 mm; B:90 mm; Specific dynamic load factor K:25 N/mm²; a:4.5 mm; Coefficient of friction µ min.:0.08; D:150 mm; h:131.5 mm; α:124 °; d:130 mm; B1:10 mm; Permissible sliding velocity v max.:0.5 m/s; |
| VLA200644-N INA Slewing Ring Bearings | Enclosure:Open; dc (min):110 mm; dd (min):119 mm; Configuration:Single Row; D:180 mm; Radial Clearance:0.050 to 0.085 mm; Limiting Speed - Oil:3,600 rpm; Fillet Radius/Chamfer:3 mm; Inside Ring Outside Diameter:108 mm; ra1 (max):2.5 mm; B:60 mm; Dynamic Load Rating:390,000 N; Limiting Speed - Grease:3,000 rpm; ra (max):2.5 mm; d:85 mm; Static Load Rating:485,000 N; db (min):99 mm; db (max):106 mm; |
| VSI200414-N INA Slewing Ring Bearings | Calculation factor Y1:0.73; Calculation factor kr:0.095; Basic dynamic load rating C:312 kN; r1,2 min.:2.1 mm; a:146 mm; K:7.5 mm; Basic static load rating C0:520 kN; Calculation factor X:0.62; Fatigue load limit Pu:13.4 kN; Mass bearing:17.6 kg; B:76 mm; D:309.5 mm; Calculation factor Y2:1.17; ra max.:2.1 mm; Calculation factor e:0.86; Reference speed:2000 r/min; d1 ≈:252.5 mm; da min.:225 mm; |
| HT10-54E1Z Kaydon Slewing Ring Bearings | ra max.:1.5 mm; H:53 mm; Minimum load factor A:48; Fatigue load limit Pu:40.5 kN; Reference speed:600 r/min; da min.:791 mm; Mass bearing (including seat washer where applicable):30 kg; D:820 mm; Basic static load rating C0:3050 kN; Basic dynamic load rating C:364 kN; D1 ≈:752.5 mm; Limiting speed:850 r/min; Da max.:779 mm; d:750 mm; r1,2 min.:1.5 mm; d1 ≈:817.5 mm; |
| 16381001 Kaydon Slewing Ring Bearings | Oil level, max.:155 mm; dc min.:258 mm; H2:100 mm; d1:270 mm; da:240 mm; H1:340 mm; Oil fill, max.:6.9 l; r:4 mm; Appropriate attachment bolt, size G:36 mm; Pa:840 kN; AA:394 mm; B1:150 mm; bc:266 mm; Cap bolt, size:M 30x200; H:625 mm; N1:42 mm; AB:420 mm; O1:216 mm; L:900 mm; |
| MTE-47 Kaydon Slewing Ring Bearings | r1:0.5 mm; Bore Type:Cylindrical Bore; Enclosure:Single Shield with S; D:72 mm; Limiting Speed - Grease:9,800 rpm; da (min):42 mm; Cy (max):4.6 mm; D1 (max):68.8 mm; Dynamic Load Rating:25,700 N; d:35 mm; Snap Ring Outside Diameter:78.6 mm; Limiting Speed - Oil:11,000 rpm; Dx (min):80 mm; Factor fo:13.8; ra (max):1 mm; Snap Ring Width:1.6 mm; Fillet Radius/Chamfer:1.1 mm; Configuration:Single Row; |
| 16335001 Kaydon Slewing Ring Bearings | Permissible sliding velocity v max.:0.5 m/s; α:124 °; h:86.5 mm; Coefficient of friction µ min.:0.08; d:85 mm; Tolerance shaft:e7; B1:8 mm; Specific dynamic load factor K:25 N/mm²; Mass bushing:0.77 kg; D1:110 mm; Tolerance housing:H7; B:40 mm; D:100 mm; a:2 mm; Permissible sliding velocity v min.:0 m/s; Coefficient of friction µ max.:0.15; Specific static load factor K0:45 N/mm²; |
| 16300001 Kaydon Slewing Ring Bearings | ra max.:2 mm; Da max.:258 mm; K:7.5 mm; Calculation factor Y2:3.6; r1,2 min.:2.1 mm; Calculation factor e:0.28; b:13.9 mm; Fatigue load limit Pu:129 kN; B1:119 mm; B2:32 mm; da max.:180 mm; Mass bearing + sleeve:27.3 kg; B:86 mm; D:270 mm; d1:140 mm; Calculation factor Y1:2.4; d2 ≈:180 mm; d3:210 mm; db min.:170 mm; Basic static load rating C0:1400 kN; |
| 16368001 Kaydon Slewing Ring Bearings | dc (min):122 mm; db (max):117 mm; Bore Type:Cylindrical Bore; ra1 (max):2 mm; Limiting Speed - Oil:3,800 rpm; db (min):112 mm; Limiting Speed - Grease:3,200 rpm; Radial Clearance:0.075 to 0.110 mm; Da (max):168 mm; ra (max):2 mm; B:46 mm; Enclosure:Open; Configuration:Single Row; Inside Ring Outside Diameter:120 mm; D:180 mm; d:100 mm; Static Load Rating:335,000 N; Dynamic Load Rating:257,000 N; Fillet Radius/Chamfer:2.1 mm; |
| 16286001 Kaydon Slewing Ring Bearings | Coefficient of friction µ min.:0.06; Coefficient of friction µ max.:0.15; B:15 mm; Specific static load factor K0:80 N/mm²; Permissible sliding velocity v min.:0 m/s; D:16 mm; Tolerance shaft:h9; d:14 mm; Tolerance housing:H7; Specific dynamic load factor K:40 N/mm²; Permissible sliding velocity v max.:1 m/s; Mass bushing:0.0011 kg; |
| HT10-60E1Z Kaydon Slewing Ring Bearings | Specific dynamic load factor K:140 N/mm²; Mass bushing:0.97 kg; Permissible sliding velocity v min.:0 m/s; B:150 mm; Effective load carrying cross section A:20720 mm²; Coefficient of friction µ max.:0.08; Specific static load factor K0:200 N/mm²; Permissible sliding velocity v max.:0.5 m/s; Coefficient of friction µ min.:0.03; d:155 mm; D:140 mm; Tolerance shaft:h8; Tolerance housing:H7; |
| VU36068 INA Slewing Ring Bearings | Mass bearing:15.5 kg; Limiting speed:800 r/min; d1:437 mm; D:440 mm; ra max.:2 mm; D1:363 mm; Da max.:380 mm; Reference speed:400 r/min; Minimum axial load factor A:1.4; da min.:420 mm; Fatigue load limit Pu:290 kN; Basic dynamic load rating C:680 kN; Basic static load rating C0:4150 kN; B:14 mm; H:48 mm; d:360 mm; r1,2 min.:2 mm; |
| KH-275P Kaydon Slewing Ring Bearings | B:80 mm; +:0.2 mm; Limiting speed:750 r/min; K:3.5 mm; ra max.:1.5 mm; Snap ring in accordance with DIN 471:170x4; das:128 mm; b1:6 mm; d1 ≈:132 mm; D:170 mm; Snap ring Seeger:SW 170; Fatigue load limit Pu:81.5 kN; Ca2:62 mm; r min.:1.8 mm; Mass bearing:6.45 kg; C2:4.4 mm; b:4.2 mm; da min.:117 mm; Calculation factor kr:0.4; Basic static load rating C0:695 kN; |
| VSU200414 INA Slewing Ring Bearings | B1:46 mm; Hydraulic nut:HMV 16 E; d3:105 mm; d:80 mm; d1:68.263 mm; G:M 80x2; B:15 mm; B4:17 mm; Mass adapter sleeve assembly:0.87 kg; |
| RK6-37N1Z Kaydon Slewing Ring Bearings | D:260 mm; Retainer Material:Pressed Steel; Nr. of Holes:6; Groove Width A:12 mm; Da (max):246 mm; d:120 mm; Static Load Rating:765,000 N; Hole Diameter (do):5 mm; Bore Type:Tapered Bore; Limiting Speed - Grease:2,100 rpm; B:55 mm; Limiting Speed - Oil:2,500 rpm; Enclosure:Open; ra (max):2.5 mm; Axial Load Factor Y0:3.10; Fillet Radius/Chamfer:3 mm; Constant e:0.21; Weight:15.300 kg; Center Guidance:Floating Steel Ring; |
| No. | Brand | T | E | D | d | N | f | M | w |
| 16387001 | Kaydon | - | - | - | 28 mm | - | - | - | - |
| VU140179 | INA | - | - | 870 mm | 529.91 mm | - | - | - | - |
| RK6-22E1Z | Kaydon | - | - | 180 mm | 85 mm | - | - | - | - |
| MTO-87 | Kaydon | - | - | 370 mm | 220 mm | - | - | - | - |
| VLU200414 | INA | - | - | 140 mm | 80 mm | - | - | - | - |
| HT10-42N1Z | Kaydon | - | - | 75 mm | 50 mm | - | - | 3 mm | - |
| VU140325 | INA | - | - | - | 65 mm | - | 8 mm | 62.5 mm | - |
| 16332001 | Kaydon | - | - | - | 150 mm | - | - | - | - |
| RK6-43P1Z | Kaydon | - | - | - | - | - | - | - | - |
| KH-325E | Kaydon | - | - | - | - | - | - | - | - |
| 16351001 | Kaydon | - | - | - | - | - | - | - | - |
| HS6-33P1Z | Kaydon | - | - | - | - | - | - | - | - |
| MTE-265T | Kaydon | - | - | - | 1000 mm | - | - | - | - |
| HS6-16E1Z | Kaydon | - | - | - | 200 mm | - | - | - | - |
| MTE-470T | Kaydon | - | - | 460 mm | 220 mm | - | - | - | - |
| HT10-42P1Z | Kaydon | - | - | - | - | - | - | - | - |
| 16352001 | Kaydon | - | - | - | - | - | - | - | - |
| 16300001 | Kaydon | - | - | 270 mm | - | - | - | - | - |
| 16381001 | Kaydon | - | - | - | - | - | - | - | - |
| VSU200414 | INA | - | - | - | 80 mm | - | - | - | - |
| HT10-48E1Z | Kaydon | - | - | - | - | - | - | - | - |
| 16384001 | Kaydon | - | - | - | - | - | - | - | - |
| 16329001 | Kaydon | - | - | 830 mm | - | - | - | - | - |
| 16269001 | Kaydon | - | - | 480 mm | - | - | - | - | - |
| VU36068 | INA | - | - | 440 mm | 360 mm | - | - | - | - |
| 16292001 | Kaydon | - | - | - | - | - | - | - | - |
| 16326001 | Kaydon | - | - | - | - | - | - | - | - |
| 16336001 | Kaydon | - | - | 19 mm | 10 mm | - | - | - | - |
| XSU080188 | INA | - | - | - | 38.1 mm | 21.5 mm | - | - | - |
| VSI250755-N | INA | - | - | - | - | - | - | - | - |
HT10-36N1Z Kaydon Slewing Ring Bearings Video
HT Internal Gear | Socare USA
SCB-HT-N-914, HT10-30N1Z, 36.160, 24.160, 411, 33.250, 24, 27.250, 30, 24.800, 2.5, 62, 21783, 340,000. SCB-HT-N-1066, HT10-36N1Z, 42.160, 30.160
Kaydon HT10-36N1Z Slewing Ring Turntable Bearing | Lily
Specifications. Part Number, HT10-36N1Z. Maximum Allowable Gear Tooth Load (Fz), 21195. Moment Load Rating (Crm), 395700. Bearing Types, Slewing
HT10-36N1Z KAYDON类型转盘轴承生产厂家, 尺寸规格表查询
产品说明. 型号, HT10-36N1Z. 最大允许轮齿负载(Fz), 21195. 额定载荷(Crm), 395700. 轴承类别, 回转支承. 外形尺寸及重量. 外圈外径(Do), 42. 内圈内径(di), 30.16
HT Series - Kaydon Bearings
HT10-30N1Z. 36.000. 24.160. 411. 33.250. 24. 27.250. 30. 24.800. 2.5. 62. 21,783. 340,000. HT10-36N1Z. 42.000. 30.160. 517. 39.250. 28. 33.250. 32. 30.800
load chart for part number HT10-36N1Z - Kaydon Bearings
Kaydon load chart. HT10-36N1Z. Back to online catalog. Use the Slewing Ring Bearing Selector to enter specific static load parameters. Show load chart with
HT10-36N1Z KAYDON美国开顿回转支承HT10-36N1Z-供货
Jun 30, 2017 - KAYDON转台轴承HT10-36N1Z是用来连接两个相邻的结构，允许它们相对旋转并传递载荷的部件。为了更好的做到这一点，转台轴承通常包括一个
Kaydon code HT10-36N1Z four point contact ball slewing
Quality Slewing bearing manufacturers & exporter - buy Kaydon code HT10-36N1Z four point contact ball slewing bearing with internal gear/teeth from China